Fireye EB700 chassis for E110 flame monitors. The chassis contains a transient suppressing device connected internally across hot and neutral and then to the internal bracket.

Fireye 120 volt, 50/60Hz chassis that includes dust cover for use with M-Series II controls.

Fireye 120 volt, 50/60Hz standard plug-in board control module chassis for use with MicroM controls.

Fireye 120 volt, 50/60Hz chassis with alpha-numeric display interface to ED510 for use with MicroM controls.

Fireye 120 volt, 50/60Hz chassis with remote reset for M-Series II controls.

Fireye 120 volt, 50/60Hz chassis with local reset with independent relay outputs M-Series II controls.

Fireye 120 volt, 50/60Hz chassis with UV self-check amplifier and 1" threads.

Fireye E1R1 auto check infrared flame amplifier module for use with a flame monitor system. These modules provide flame scanning using any of the Fireye AutoCheck infrared scanners, standard ultraviolet scanners, flame rod, and ultraviolet self check scanners. After scanner selection the proper amplifier module must be inserted in the flame monitor chassis.

Fireye EUV1 standard UV flame amplifier module for use with a flame monitor system. These modules provide flame scanning using any of the Fireye AutoCheck infrared scanners, standard ultraviolet scanners, flame rod, and ultraviolet self check scanners. After scanner selection the proper amplifier module must be inserted in the flame monitor chassis.

Fireye EP160 programmer module for use with the flame monitor burner management control system. This unit features a 30-second purge, 10-second PTFI and MTFI ignition timing, and 4-second FFRT. Fireye programmers provide start-up programming, safe-start check, and flame monitoring supervision.

Fireye UV1A3 non self-checking flame scanner with 3 foot cables and a 1/2" treaded coupling. UV scanners are recommended for detecting flames from standard fuel gases, some waste gases, and light oil fuels.

Fireye UV1A6 non self-checking flame scanner with 6 foot cables and a 1/2" treaded coupling. UV scanners are recommended for detecting flames from standard fuel gases, some waste gases, and light oil fuels.

Fireye E110 flame monitor burner management control for use with microprocessor-based EP and EPD style programmer modules. The E110 is designed to provide the proper burner sequencing, ignition and flame monitoring protection on automatically ignited oil, gas, and combination fuel burners.

Fireye UV2 36" non self-checking flame scanner with a 3/8" NPT female to 1/2" NPT male adapter that fits into the 1/2" threaded coupling of models UV1A3 and UV1A6. UV scanners are recommended for detecting flames from standard fuel gases, some waste gases, and light oil fuels.

Fireye ED510 display module for use with Fireye flame monitor and MicroM burner management controls. The ED510 features two line by sixteen character backlit LCD display, continuous display of current burner operating status, including first out annunciation in the event of a lockout condition, and three key, tactile dome keypad to provide historical information of the burner.

Fireye self-checking ultraviolet scanner for continuously fired applications where recycling is infrequent or absent. This unit checks the electronics and the UV tube for proper operation every four seconds during the firing period and is suitable for fuel gases or oil. It features a replaceable UV tub, shutter mechanism, 8-foot lead fires, and a 1" NPT/BSP mounting pipe thread.

Fireye program module with relight function for use with M-Series II controls.

Fireye program module with selectable purge timing, trial for ignition timing, and recycle/non-recycle operation for use with M-Series II controls.

Fireye 2-4 second FFRT UV amplifier for use with M-Series II controls.

Fireye 2-4 second FFRT flame rectification amplifier for use with M-Series II controls.

Fireye 3-4 second FFRT UV amplifier for use with MicroM controls.

Fireye program module with selectable purge timing (7, 30, 60, and 90 seconds) PTFI timing, recycle/non-recycle, post purge, and prove air open at start for use with MicroM controls.

Fireye flame rod/photocell amplifier, with 4 second (max) FFRT, for use with MicroM controls.

Fireye infrared flame scanner with 8-foot cable and 90° head. This scanner contains a low impedance detector and detects low flicker frequency IR signals from gas and oil flames. For use on D-Series, FlameMonitor, FlameWorx, MicroM, and Burnerlogix controls.

Fireye program module that provides dip switches to select purge time (7, 30, 60, and 90 seconds), 5/10 second PTFI, Air Flow Proven Open at Start, Post Purge, Recycle or Non-recycle. Provides 8 second pilot stabilization period and 10 second main trial for ignition. Run/check switch included. for use with MicroM controls.

Fireye infrared flame scanner with 4-foot cable, 90° head, and 1/2" NPT mounting collar. This scanner contains a low impedance detector and detects low flicker frequency IR signals from gas and oil flames. For use on D-Series, FlameMonitor, FlameWorx, MicroM, and BurnerLogiX controls.

Fireye program module with 10-second PTFI relight operation for MicroM controls.

Fireye infrared flame scanner with 4-foot cable, straight head, and 1/2" NPT mounting collar. This scanner contains a low impedance detector and detects low flicker frequency IR signals from gas and oil flames. For use on D-Series, FlameMonitor, FlameWorx, MicroM, and BurnerLogiX controls.

Fireye non-self check UV scanner with 1/2" NPT connector and 12' flex conduit for use with M-Series, M-Series II, MicroM, FlameWorx, MB-2 and D-Series controls as well as the Flame-Monitor, BurnerLogiX, and Nexus systems.

Fireye program module with 30-second purge for use with Flame-Monitor controls.

Fireye program module with selectable purge timing, pilot trial for ignition timing, pilot stabilizing period, and recycle/non-recycle operation for use with M-Series II controls. It also features a 10-second main flame trial for ignition and a run-check switch.

Fireye program module with selectable purge timing, 10-second main flame trial-for-ignition, trial for ignition timing, pilot stabilizing period, and recycle/non-recycle operation for use with two-stage burners.

Fireye UV amplifier with 0.8-second FFRT for use with MicroM controls.

Fireye 90° right angle UV scanner with 6' unshielded lead wires for M-Series, M-Series II, and MicroM controls.

Fireye program module with recycle on main flame fail, 15-second purge, 7-second fixed PTFI, 5-second pilot proving 5-second MTFI, early spark termination, and interrupted pilot for MicroM controls. It also features recycle on air flow failure, no post purge, run/check switch, and reset on line voltage.

Fireye infrared flame scanner with 8-foot cable, straight head, and 1/2" NPT mounting collar. This scanner contains a low impedance detector and detects low flicker frequency IR signals from gas and oil flames. For use on D-Series, FlameMonitor, FlameWorx, MicroM, and Burner Logix controls.

Fireye program module with 30-second purge, start-up programming, safestart check, and flame monitoring supervision for use with Flame-Monitor controls.

Fireye flame safeguard control compact burner management system designed to provide automatic ignition and continuous flame monitoring for commercial sizes of heating and process burners that use gaseous fuels.

Fireye UV integrated flame scanner with 4-second FFRT and 1" mounting flange. This flame scanner features an internal single pole, single throw (normally open) flame relay with a fixed on/off threshold to provide flame on/flame off indication, eliminating the need of an external flame amplifier. The scanner utilizes an ultra-violet tube type sensor, and electromechanical self-checking shutter mechanism.

Fireye flame rod/photocell amplifier module with 0.8-second FFRT for MicroM controls.

Fireye UV amplifier module with 0.8-second FFRT for M-Series II controls.

Fireye UV non-self check BurnerLogiX chassis/flame amplifier module with mounting screws and blank display module.

Fireye MicroM programmer module with non-recycle on flame fail, 30-second purge, 5-second fixed PTFi, 8-second pilot stabilization period, intermittent pilot, 15-second post purge, and prove air open at start.

Fireye EP161 programmer module for use with the flame monitor burner management control system. This unit features a 30-second purge, 10-second PTFI and 10/30-second MTFI ignition timing, and 4-second FFRT. Fireye programmers provide start-up programming, safe-start check, and flame monitoring supervision.

Fireye 4-second (max) FFRT self-check UV amplifier for use with MicroM controls.

Fireye UV integrated flame scanner with internal flame relay featuring selectable FFRT and quick disconnect.

Fireye UV integrated flame scanner with internal flame relay featuring selectable FFRT and quick disconnect.

Fireye 12" flame rod with 1/2" NPT mount for C-, D-, and M-Series controls.

Fireye 1/2" NPT heat insulator for 48PT and UV1A flame scanners.

Fireye cabinet mounted open wiring base for MicroM controls.